How To Fix Old Whirlpool and Kenmore Dryer
If you have an old Whirlpool or Kenmore Dryer, not working, can be solved. You can save a lot of money to put to you. Otherwise get a huge bill for repairs could, if someone can solve the problem. It will really save a lot if you do not buy a new one. And guess what? If you do well, will dry your clothes better and more quickly and efficiently, as many new ones.
Well, only a security Tip: Make sure the dryer is removed from powerBefore you start working on it!
To facilitate this work, loosen the vent pipe from the back. This is usually a 4 "flexible aluminum pipe that carries away the hot air and lint from the dryer, if it works. Now you must determine what the problem was, or what makes it drier. If it works well, but not hot? "It was the air cold and dry clothes. There are some things that can cause this expulsion. from the back of the dryer. Is attachedwith more than ΒΌ "or 3 / 8" screws. Watch the wires. Check all, also connected to the heating element, thermostats, etc. Take advantage of the location of lines and ensure that everything is in order. Use a flashlight or light worth seeing, if necessary. Sometimes there is one that has been burned at the terminal is disconnected. This can be easily repaired by cutting the end burnt and commissioning of a new cap end.
If the wiring is OK, checkThermostats, the little round gadget on the heating element. This can be easily done by removing the wires from them, and with a continuity tester to see if current can flow through them. If there is an open circuit, replace it with a new one. If they are correct, check the heating. Most dryers heating elements with two terminals. Remove the cables and switch to heating with a continuity tester.
You can use a continuity tester buy in the store for about $ 15. Youalso a simple way, with a flashlight battery, bulb, and a bit 'of wire. Solder a piece of wire on the bottom of the battery, and another piece of the top of the battery. Solder the wires on one side of the bulb. No matter which wire. Solder a wire to the top of onions. Ends up with only two wires that are left. The tester is built! Check it by the two wires together. The bulb should go on. Now just press the two wires, the heater twoTerminals, or terminals thermostat. When the lamp comes on, so that part is fine.
When the installation is bad when buying a new replacement. So we take the old item loosening the top of the machine, and they need to travel. This is accomplished by pressing a spatula between the top and front of the cabinet, about 3 "from the side of the dryer on both sides. These are the two hinges that first down to keep it. At the same time, a pressure flat screwdriverbetween the top and the cabinet in the middle of the forehead. If the fasteners are released, you can easily lift the front, and can be moved back and is based on a wall behind the dryer. If the top is not easy trying to raise the issue to find the clip and slide it back with a spatula. On top of the heating element is a screw. This is all that keeps the heater fits go to the bottom of a gutter to keep it. Draw a picture of where the cables are connectedThe heating element and thermostat or thermostats. Then remove the cable from the heating and thermostats on the side of the housing oven. Take a screw on top of the house. Slide the housing back until it exits the slot it rests so you can pick it up, if the lowest places, and can be easily removed from the bottom rear of the dryer. Remove one screw at the bottom of the heater and pull out of the house. Enter the new national andfasten with the screw. The assembly is the element of resealing and dryer all, including cables, back, etc. Connect the power cord and turn the dryer to make sure it heats.
When the thermostat, wiring and heating element is good then the problem in one of the contacts at the top of the house, or even the engine. It has a safety switch, which together with the heater. This is to extinguish the fire when the engine stopped, so that clothes do not burn.
WhenDryer heats, but only very high, replacing the two wheels that keep the drum up a. He also replaced the idler on the belt. They can be reached from inside the lower front of the dryer. If the engine is running, but drum does not rotate, replace the belt. If the motor hums, but does not replace the unit. There are many other things that can go wrong with the dryer, but these are some of the most important. Good luck! Warning! Make sure nothing is plugged in before!
Related posts:
- Whirlpool Dryer Parts
- Washer and dryer selection, Select American
- 3 Important safety information you need to know when a condenser dryer
- You should fix your appliance?
- How to Change Your Whirlpool Refrigerator Evaporator Fan Motor